The 7-Step Jif Marine Hinged Dock Ladder # JIF87FR is 83-1/2" from the top of the deck surface to the bottom step. The 6-Step # JIF77FR is 71-3/4" from the top of the deck surface to the bottom step. view full answer...
The step height for the Jif Marine Hinged Dock Ladder - 5 Steps - 750 lbs - Aluminum - 4" Deep Step # JIF67FR is 12". This is the same as the rung to rung measurement. In other words, each step is 12" apart. view full answer...
The outside dimensions of the Taylor Made Low-Profile Boat Guide Wheel for 1-1/2" Diameter Dock Pipes part # 3691214 are 14" diameter x 6" wide. view full answer...
The hole for the LED Boat Docking Lights - Recessed Mount - Waterproof - 12V/24V - Qty 2 # TN83ZR is an oval shape. The hole is 4.25" x 2.3" and you will be able to use the gasket as a template to cut the hull.
I have attached a dimensional drawing which shows the gasket and housing measurements for your reference. view full answer...
It sounds like the Halogen lights you are using are pulling too much power causing you to blow the breaker once they heat up. I recommend changing them to LED's like the LED Pontoon and Fishing Boat Docking Lights item # TN23ZR. view full answer...
The TorkLift GlowStep Stow N' Go Scissor Steps # TLA7844 is going to extend out roughly 38 inches from where it installs. I say roughly since it's a scissor step and how far the steps extend changes the distance they stick out. view full answer...
You should be just fine with the clearances you listed for the CE Smith Guide-Ons part # CE27600.
3 inches would be great for the horizontal clearance between the guide ons and the pontoons and 1-1/2 inches of vertical clearance would be just fine as well. view full answer...
We measured the length of the standoffs that come with the Jif Marine Telescoping Gunwale Hook Ladder # JIF53FR and they are 4-1/4 inches long. view full answer...
I have attached a diagram I made of the bolt dimensions of the Jif Marine Telescoping Drop Ladder with Hand Grips - 3 Steps - 34" Tall - 400 lbs - Stainless Steel item # 315-EQB3. The pre-drilled mounting bracket with 1/4" holes are spaced 10-1/8" apart. So if you old ladder has a similar mounting style this should work great for your Chaparall Boat. view full answer...
The distance between the mounting holes on the Sliding Under Platform Pontoon Boat Ladder part # 315-FOG4 left to right on center is 10-3/16". view full answer...
The Sliding Under Platform Pontoon Boat Ladder # 315-FOG3 has mounting hole spacing of:
- 1-13/16" between the holes closest together on the same side and end
- 6-1/4" between the holes closest together on the opposite end of the same side
- 9-7/8" between the holes furthest apart on the opposite end of the same side
- 10" between the holes directly across on the opposite side
I have included a diagram showing these measurements to help understand the spacing. view full answer...
I spoke with my contact at DeeZee about the Invis-A-Rack # DZ951800. She stated that the maximum length of the crossbars on the rack is 69 inches so that is more than enough room for your 51 inch wide Jon boat. I have linked a video featuring this ladder rack for you. view full answer...
I attached a diagram that shows the various dimensions of Sliding Under Platform Pontoon Boat Ladder - 3 Steps - 34-1/2" Tall - 400 lbs - Stainless Steel # 315-FOG3. The mounting brackets measure 11-7/8" long, 12" from outside edge to outside edge, and the brackets are 1-5/8" wide. I also attached a demonstration video for you. view full answer...
The hook depth on the Jif Marine Gunwale Hook Ladder # JIF93FR is 11". This means that as long as your gunwale is 11" or less you would be able to hook the ladder over the gunwale on your boat. view full answer...
When installed, the ladder itself will extend out 16 inches further than the face of the ladder its mounted to. The distance it extends past that will depend on the bikes placed on the rack. I have edited a photo for you showing this dimension.
The bike pedals should be more or less even with the end of the rack arm, but the handlebars will extend out further than that. If this does not provide you with enough clearance, you can loosen the bolt on your handlebar gooseneck enough so that... view full answer...
The pin you mentioned is the Replacement Hitch Bolt and Clip for Yakima HoldUp and BigHorn Bike Carriers # Y8890200. This replaces a threaded hitch bolt and clip for a Yakima HoldUp (Y02419, Y02433, or Y02443), Yakima BigHorn 3 (8002524), Yakima BigHorn 4 made between 2000 and 2003 (8002513), or Yakima Getaway. Also works for Yakima DryDock (Y02589) boat carrier. This is used to secure the bike rack to the hitch.
Hitch bolt dimensions:
Overall length: 4-9/16"
Usable length: 3-1/2"
Thread... view full answer...
I spoke to my contact at Curt about the Curt Solid Steel 2" Hitch Bar part # D36 and they informed me that it does not have a weight rating because it is not in the finished form. The weight capacity will vary depending on the length and amount of gussets or reinforcements that are used.
If you need something with an exact weight rating you may want to look at the Draw-Tite Ball Mount part # 4285 which has a 12" long shank (center of hitch pin hole to center of ball hole), comes with... view full answer...